A c t a    M e ch a t r o n i c a
International Scientific Journal about Mechatronics
ISSN 2453-7306



Editorial Board


Instructions for authors

Open Access Policy




6. 2021 04
6. 2021 03
6. 2021 02
6. 2021 01


5. 2020 04
5. 2020 03
5. 2020 02
5. 2020 01
4. 2019 04
4. 2019 03
4. 2019 02
4. 2019 01
3. 2018 04
3. 2018 03
3. 2018 02
3. 2018 01
2. 2017 04
2. 2017 03
2. 2017 02
2. 2017 01
1. 2016 04
1. 2016 03
1. 2016 02
1. 2016 01

Acta Mechatronica

Instructions for authors


  • Manuscripts: Manuscripts should be written in English. The manuscripts must be prepared electronically by template of the Acta Mechatronica and should be submitted by e-mail to address: .
    The template for the journal Acta Mechatronica (AM) is available here:

  • Sample of manuscripts: The reference and sample articles are available from the issues section of the journal website.

  • Publishing Fee: The publishing fee is 275 EUR/submission that must be paid after receiving the acceptance for publication.

  • Submission Preparation Checklist: As part of the submission process, authors are required to check off their submission's compliance with all of the following items, and submission of a manuscript may be returned to authors that do not adhere to these guidelines.
    • The submission of a manuscript has not been previously published, nor is it before another journal for consideration (or an explanation has been provided in Comments to the Editor).
    • Where available, URLs for the references have been provided.
    • The article is prepared in accordance with the instructions for authors.
    • The text adheres to the stylistic and bibliographic requirements outlined in the Author Guidelines, which is found in "Instructions" folder.
    • By sending of article for publishing in the journal Acta Mechatronica author/authors agree with the terms and conditions defined by the journal Acta Mechatronica.

  • Ethical rules: Manuscripts may be rejected by the editorial office if it is felt that the work was not carried out within an ethical framework. Plagiarism in any form constitutes a serious violation of the most basic principles of scholarship and cannot be tolerated. This policy details the responsibilities of all authors, editors and reviewers working with and for Acta Mechatronica journal as well as our own ethical responsibilities. This includes, but is not limited to, plagiarism, data falsification, misuse of third party material, fabrication of results and fraudulent authorship.

  • Manuscript preparation: The original article should be submitted electronically in double columns format. The article should has been in the range from 4(minimum) to 20(maximum) pages. A final article which would exceed more than 20 pages of the journal may be returned for abridgement. All articles must be written in British English. The article must adhere to the scientific structure of the preparation of contribution - Introduction, Main text (containing the methodological basis, experimental part, results and its discussion), and Conclusions.
    The text of the article should include the following:
    • Title: as short as possible, with no abbreviations or acronyms.
    • Address: position, department, name of institution, full postal address and email address for each author.
    • Keywords: the maximum limit are 5 words or phrases. Keywords are important for online searching.
    • Abstract: the maximum limit are 7 lines as per the template of Acta Mechatronica journal.
    • Main text: contains information about new knowledge, which have been obtained from research, study, or the proposal of solution to project tasks.
    • References: Full references should include all author names and initials, the date of publication, the title of the article, the title of publication (italics), the volume and issue number (of a journal), the publisher and form (books, conference proceedings) and page numbers.
    • Acknowledgements and notes: this section contains information about the source documents from which the article is made.
    • Figures and figure captions: all illustrations, whether diagrams or photographs, are referred to as Figures. All figures have a description below the figure. All figures can be made in colours. Figures must be numbered sequentially. Please prepare all figures, especially line diagrams, to the highest possible standards.
    • Tables and table captions: all tables have a description above of table. All tables can be made in colours. Tables must be numbered sequentially. Please prepare all tables to the highest possible standards.
    • Units of measurement: Acta Mechatronica - International Scientific Journal follows the Systeme International (SI) for units of measurement.


  • Peer Review Process: After submission of a manuscript authors will receive of information about receipt of manuscript. All submitted manuscripts for Acta Mechatronica journal are sent out to peer review process. Some articles which are out of scope for the journal topic or are of an unacceptably low standard will be rejected directly without review process. Each manuscript will be blind reviewed by minimal two members of the Reviewers Committee. The review process will take time no more than 2 months. The reviewers will fill out a review form and evaluate the submitted manuscripts. Reviewers will evaluate the following points:
    1. Manuscript is relevant for the Acta Mechatronica journal.
    2. Manuscript is new and original.
    3. Manuscript is prepared clearly, logically and correctly.
    4. Language of manuscript is clear and understandable.
    5. Figures, diagrams, charts and tables of manuscript are readable, clear and good quality.
    6. References of manuscript are used correctly.
    Review process is finished of notification for authors if manuscript is possible accept without modification, accept after modification or reject.

  • Copyright Notice: The publisher has the copyright if and when the submitted article is accepted for publication. Any uses and/or copies of this journal must include the customary bibliographic citation, including author attribution, date, article title, journal title, and URL. Authors retain copyright and grant the journal right of first publication with the work. Authors allow others to share the work with an acknowledgement of the work's authorship and initial publication in Acta Mechatronica journal.

  • Privacy Statement: The names, addresses and email addresses entered in this journal site will be used exclusively for the stated purposes of this journal.

ISSN 2453-7306
© Acta Mechatronica - International Scientific Journal about Mechatronics, journal publisher is the  4S go, Ltd.   4S go
  © Acta Mechatronica   AM               

Valid XHTML 1.0 - Valid CSS3
Valid XHTML 1.0 Transitional Valid CSS3!